This time we take to the wallpaper two realizations, made at the same time. Two single-family houses in Krzywaczka, each with a total area of 157.62 m2.
Two charming and inconspicuous houses from the outside, inside they hide plenty of space for living with the whole family. Each house has a total area of 157.62 m2, including a garage, boiler room and adapted attic. The usable area is 105.2 m2. The project comes from Archon. Get acquainted with our double project in picturesque Krzywaczka, Małopolska province.
Foundations
They relied on a traditional foundation built with footings and footings. The foundation walls were built with reinforced concrete blocks. Contraction reinforcement was used: 12 mm B500SP ribbed reinforcing bars connected by stirrups of 6 mm B500SP bars. The foundation concrete blocks were poured with C16/20 concrete.
The foundations were insulated with vertical as well as horizontal insulation. The insulation was made of asphalt paper on cardboard and weldable polymer-asphalt paper on a polyester fiber matrix . Extruded polyethylene insulation film “bucket” was laid on the walls. Insulated with Styrofoam board Termonium 5,04 m3. Drainage with backfill was also performed.
The floor was insulated with Optimum-Superacoustic polystyrene board (3.42 m3).
Walls
The walls of the house were made of H+H TLMB PP4-0.50 cellular concrete block in two sizes: 625x240x250 mm – 774 pieces, and 625x115x250 mm – 465 pieces. The blocks were cemented together with white glue for cellular concrete elements.
The walls were insulated with GOLD facade polystyrene board 0.038 W/(m2K), which was used about 36.70 m3.
The walls inside were plastered with cement plaster by hand.
First floor
On the first floor you will find many utility rooms. The kitchen occupies 8,76 m2. The living room with dining room is 26,22 m2 of space, while the toilet is 1,77 m2. There is also room for a pantry (2,46 m2) and a boiler room (5,27 m2). The first floor is complemented by a 4.37 m2 vestibule and a hall of 5.14 m2.
The windows in the walls on the first floor are PVC windows with a total area of 17.95 m2. PVC balcony doors of 24 m2 were also installed. The heat transfer coefficient for the windows and balcony doors was below 0.9 W/(m2K), which indicates the high energy efficiency of the house. Of course, an exterior, burglar-proof, pine wood entrance door was installed.
Ceiling
The ceiling was made of a reinforced concrete slab. It was reinforced with bars along with the rim (8 and 10 mm). The ceiling was made at a height of 278 cm from the first floor.
Attic
We get to the attic by a beech wood staircase, with a total area of 6,05 m2. The lobby (5,89 m2) we can go to the bathroom (6,75 m2), two rooms (2×10,20 m2), a slightly smaller room of 9,33 m2 and a dressing room (2,79 m2). The total usable area of the attic is 51,21 m2.
The floor was insulated with GOLD polystyrene slabs roof-to-floor 0.036 W/(m2K). of which 9.09 m3 were used. The attic, on the other hand, was supplemented with 150 mm mineral wool boards, 151 m2 of which were used.
A blind floor of 2.5 cm thick particleboard was also created in the attic, which can be accessed by the LWS-280 folding attic staircase.
Roof
The roof, with a 40-degree pitch, was created from foundations more than 2 meters long. Then the masonry and columns were laid. Top frames and purlins more than 3 meters long, and ordinary rafters more than 4.5 meters long. Inside, soffits were made of 19 mm thick boards and varnished. Beautiful ceramic tiles (about 1839 pieces) were laid on the roof.
FAKRO’s 78×140 cm double-glazed pine roof windows were also installed. Three such windows were installed.
Chimney and heating
The chimney was created from the basic elements of a single-circuit chimney with ventilation Schiedel Rondo Plus with a diameter of 20 cm. The chimney was prepared for gas heating. Underfloor heating was also laid throughout the house.
The house also uses gravity ventilation.
